Before injecting an anabolic steroid into your body, there are many things to consider. You should have proper knowledge or proper supplies and maintain proper sterility. When you ignore the procedure or do not prepare adequately, it can lead to inflammation, infections, abscesses, scar tissue development, muscle damage, nerve damage, and even fatality.
Proper sterility should be maintained, for example, you should never re-use pins, share them with others, or try to sterilize them by rubbing them with alcohol or exposing them to flame. Dangerous diseases can be transmitted like this. Proper procedures should be followed and utmost safety should be maintained. Here are a few pre-injection tips.
Check the product for the expiry date. Some medicines lose their potency over time.
Re-check the ampoule or the vial to make sure that it contains the substance you intend to inject yourself with.
Make sure that all materials are kept sterile, during the injection process. The syringe, the pin, and the swab should be sealed when you open them. Do not use any items whose package has been breached.
Do not start preparing the injection without washing your hand.
The injection site should be disinfected with an alcohol swab.
The syringe should not contain any air bubbles.
Once you remove the protective cover over the pin, do not touch the pin to anything.
After you have finished injecting yourself, make sure that you not prick yourself or anyone else with it.
Syringes should never be preloaded. Many people do this, but it should be avoided even if it is only for a few minutes. Injectable anabolic steroids contain solvents which may eat into the plastic in the syringe and the rubber plunger, melting it. If you use such pre-loaded syringes, you risk injecting yourself with rubber particulates and toxic substances that may have dissolved in the liquid.
Correct pin and syringe for injections
Before you try to self inject anabolic steroids, you should understand the different terms. Volumes are usually denoted in millimeter or cubic centimeter, both are the same quantity.
While the body part or the muscle, where the syringe is going to be injected, is an important deciding factor, it is not the only one. The type of liquid that you are going to inject is also important.
Water-based anabolic steroids can be injected through small gauge pins, while oil based anabolic steroids should be injected through a large gauge pin. You might want to know what is meant by gauge Gauge is nothing but the thickness of the pin. As the gauge number of a pin increases, the thickness of the pin decreases. For example, a 30 g pin is actually thinner than a 19 g pin. Gauge is not a reference to the pin's length.
Note that when you choose a small gauge pin to inject an oil based substance, it will take more time to pull liquid from the container and to inject the liquid.
How to inject
If you are going to start your first cycle soon, 'how to inject' is probably that last thing that you are worried about. You would have started by conducting research on the different injectable anabolic steroids available in the market, which How To Inject Steroidsyou think can help you reach your goal. But when you have the vials and the syringes in front of you, you will surely think about how you will get the steroid out from the bottle and into your body. At this point, some people will become exasperated and even give up. Here is some information on injecting anabolic steroids.
Draw some air into the syringe and inject it into the vial. The pressure in the vial will increase and drawing the liquid into the vial will become easier. Make sure that the tip of the pin is under the liquid and then pull the plunger back slowly, to draw the volume of liquid that you desire.
If you want, you can change the needle after this. The needle may have lost some of its sharpness as it made its way through the stopper and may cause some discomfort when you prick your skin with it.
Clean the area, which you are going to inject into, with a fresh alcohol swab. Place the pin over the area and simply push it fully. Draw the plunger back a little. If you notice any blood inside the syringe, you have probably hit a vein or an artery and you need to choose another spot. Repeat the same procedure again.
After a few seconds, remove the pin and immediately cover the injection area with a fresh cotton ball and press for a few seconds. If you see a little blood, it is okay. You just pierced the skin and some blood is bound to come out.